Introduction
Depending on the causes, severity, and location of an unstable shoreline, one or more approaches can help stabilize your shoreline while protecting habitat, water quality, and property values. The approaches are organized into four levels that range from low cost for minor erosion problems (Level 1) to high cost for significant erosion problems (Level 4). This table summarizes the strategies for each of the four levels.
Level 1: Vegetative stabilization
A vegetative buffer is an intentionally protected area of deep-rooted native vegetation along the water’s edge. Vegetative buffers provide many benefits to a shoreline, including erosion prevention, water quality protection, scenic beauty, privacy from boaters and neighbors, habitats for fish and wildlife, and fewer geese on your lawn or beach.
A functional vegetation buffer includes three layers of vegetation: trees, shrubs, and ground cover. Ground covering should be natural, native species of wildflowers, grasses, sedges, and ferns.
Without much technical knowledge or cost, many shoreline property owners are implementing the two basic practices that keep vegetative buffers healthy - no mow and native plantings.
NO MOW
Allowing natural regeneration of native plant species is a simple method to reestablish a vegetative buffer zone. Focus on areas with weak or no turf grass and with limited foot traffic.
A native vegetative buffer is a more durable landscape that filters pollutants in runoff than a high-maintenance lawn that does not filter pollutants and increases nutrient pollution runoff to the lake. One way to make a no mow area more attractive is to add edging, border plantings, rock borders, and birdhouses landward of the area.
NATIVE PLANTINGS
Planting native plant species is another way to reestablish a vegetative buffer zone. Depending on the type of plantings, this zone can be a diverse collection of species, as well as pollinator habitat.
There are many different types of native plants property owners can choose to enhance their buffer zone. Attention and care by the property owner is needed to ensure the plants establish and remain healthy.

Before

During

After
Photos: Rob Langer (Natural Shore)
Level 2: Bioengineering
Bioengineering uses a combination of native plants and natural or biodegradable materials to protect the shoreline. Bioengineering practices can reduce erosion, stabilize the shoreline, and provide habitat for wildlife. It can also be used upland or at the lake edge to reduce sediment, nutrient, and pollutant runoff entering the lake.
NATURAL FIBER ROLLS AND LOGS
Natural fiber rolls consist of natural materials like wood excelsior, coconut husk fiber, straw, or flax wrapped in a biodegradable fiber net. Ranging from 8 to 20 inches in width and 10 to 20 feet in length, these rolls are often placed along the shoreline to stabilize banks. The rolls are held in place by dead or live stakes, with the ends buried into the ground or shoreline.
Natural fiber rolls are also commonly known as coir logs (shown below), bio-logs, wattles, filter logs, or sediment logs.

Before

During

After
Photos: Stearns SWCD
NATURAL FIBER BLANKETS
Natural fiber blankets are an erosion control device for large areas. These come in a wide variety of materials, weights, and sizes. In general, they are made from natural biodegradable materials that are rolled over a large area on the ground and anchored. They may be reinforced with a fiber mesh or webbing.
Much like other natural fiber products, native plantings and seed can be sown under or in the mat. When installed correctly, natural fiber mats reduce runoff and erosion problems and allow plants to establish root structures to stabilize the soil. The fiber blankets (shown below) biodegrade over time, feeding nutrients to the plants, and can be used in combination with natural fiber sediment logs on steeper slopes.

Before

During

After
Photos: Rob Langer (Natural Shore)
Level 3: Advanced bioengineering
Best management practices include wave reducing timbers, rock-toe with native plantings (shown below), and tiered bio-logs. These practices should be designed and installed by a person certified in their use.

Before

During

After
Photos: Washington County SWCD
Level 4: Riprap or engineered structural stabilization
This level includes vegetated riprap (shown below), riprap with native plantings above (shown below), riprap combined with bioengineering practices, riprap with upland geotextile bags, rock riprap with upland vegetated geogrid lifts, and more advanced engineering stabilization approaches. These practices should be designed and installed by a person certified in their use.
Level 4 comes with additional DNR regulatory requirements, see Shoreline Alteration: Riprap.
Vegetated riprap

Before

During

After
Photos: Washington County SWCD
Riprap with native plantings above the riprap

Before

During

After
Photos: Stearns SWCD
